C&H Technologies M218 Manuel d'utilisateur

MODEL M218 ( FORMERLY HP E2270A) USER’S MANUAL 1 6 - CHANNEL FORM A SWITCH M - MODULE Document Part No: 11029534 C&H Technologies, I

4 C&H Technologies, Inc. <> 445 Round Rock West Drive <> Round Rock, Texas 78681 <> www.chtech.com

5 2.0 INSTALLATION 2.1 UNPACKING AND INSPECTION Verify that there has been no damage to the shipping container. If damage exists t

6 2.4 PREPARATION FOR RESHIPMENT If the module is to be shipped separately it should be enclosed in a suitable water and vapor proof anti-static b

7 3.0 FUNCTIONAL DESCRIPTION 3.1 OVERVIEW A simplified functional block diagram is shown in Figure 2. A(7:1)D(15:0)CarrierInterface/IACK/CS/DS0/W

8 3.1.3 ID EEPROM The EEPROM holds sixty-four 16-bit words of M-Module ID data and VXI M-Module data. Refer to “ID EEPROM Register” on pa

9 Channel 0Channel 1Channel 2Channel 31 CH0_NO16 CH0_COM2 CH1_NO17 CH1_COM3 CH2_NO18 CH2_COM4 CH3_NO19 CH3_COMChannel 4Channel 5Channel 6Channel 75

10 3.2 IDENTIFICATION AND CONFIGURATION REGISTERS 3.2.1 I/O Registers There are a variety of registers used to configure and control the modu

11 Reg. 00 Status Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Write Read-only Read Reserved INIT MPS FIFOE FIFOF INT INIT

12 Reg. 10 Row 0 Set Register Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Write Unused R0C3 R0C2 R0C1 R0C0 Read Unused R0C3 R

13 3.2.2 Module Identification The M218 supports the identification function called IDENT. This IDENT function provides information about the

ii COPYRIGHT C&H Technologies, Inc. (C&H) provides this manual "as is" without warranty of any kind, either expressed or implied,

14 4.0 OPERATION The M218 is a register-based instrument that is controlled through a series of I/O registers described in Section 3.2.1.

15 3. The Row n Set/Reset readback registers return the programmed relay state only if you use the module correctly. Since the driver power can be

16 If the M-Module is enabled to interrupt, it asserts the INT line on the M-Module interface to the Carrier when the last commanded relay oper

A-1 APPENDIX A: CONNECTORS MAXIMUM VOLTAGE/CURRENT. The maximum voltage that may be applied to any connector on the M218, M219, or M220 is 200 VD

A-2 C&H Technologies, Inc. <> 445 Round Rock West Drive <> Round Rock, Texas 78681 <> www.chtech.com

N O T E S: C&H Technologies, Inc. <> 445 Round Rock West Drive <> Round Rock, Texas 78681 <> www.chtech.com

. C&H Technologies, Inc. <> 445 Round Rock West Drive <> Round Rock, Texas 78681 <> www.chtech.com

READER'S COMMENT FORM Your comments assist us in improving the usefulness of C&H's publications; they are an important part of the

INSTRUCTIONS In its continuing effort to improve documentation, C&H Technologies, Inc. provides this form for use in submitting any commen

iii AMENDMENT NOTICE C&H Technologies, Inc. makes every attempt to provide up-to-date manuals with the associated equipment. Occasionally, chan

iv INTRODUCTION This manual describes the operation and use of the C&H Model M218 16-Channel Form A Switch M-Module (Part Numbe

v TABLE OF CONTENTS 1.0 GENERAL DESCRIPTION... 1 1.1 P

vi LIST OF FIGURES Figure 1. M-MODULE Installation ...5 Fi

1 1.0 GENERAL DESCRIPTION The M218 provides 16 one-wire switches on a single wide M-Module adhering to the ANSI/VITA 12-1996 specificat

2 1.2.2 Specifications The M218 incorporates the standard 40-pin, 20x2 row connector interfaces to the carrier board for power and data/contro

3 1.2.3 Mechanical The mechanical dimensions of the module are in conformance with ANSI/VITA 12-1996 for single-wide M-Module modules.